RUSS' OLD RADIOS
  • HOME
  • FOR SALE
    • CURRENTLY AVAILABLE
    • DO IT YOURSELF SPECIALS
    • EXCEPTIONAL DEALS
    • WITH MP3 PORTS
  • RESTORATION
  • BLOG
  • BEFORE/AFTER
  • CONTACT US
  • UNIQUE RADIOS
  • 1920'S Superheterodyne

Acmefone from 1922

1/20/2018

5 Comments

 
The box said "AL's radio". Inside was a 3-tube Acme radio with other accessories from the early 1920's. It had been preserved so well. It must have been important to Al. Now, nearly 100 years after it was made, his nephew was allowing me to take responsibility for it's future. I will do my best.

Picture
This receiver was manufactured by Acme Apparatus Co., Cambridge MA.
Picture
As-found above

This 3 tube receiver is comprised of a UV200 detector and two stages of audio amplification. The audio stages incorporate 4 ohm rheostats controlling the filaments. These low resistance rheostats point to the original use of 1 amp UV 201s in the audio stages that would be consistent with a radio made in 1921 - early 1922. So all three tubes would have been the early brass-based/tipped 1 amp versions.

It is really tough to tell, but the original finish is either so good or possibly has been neatly top-coated at some time. In any case. the very slight cracking of the original shellac is visible if you look VERY closely.


Picture
Not only is there a storage space for B batteries, but also an internal horn speaker.
Picture
In the picture above you can see the splices that were made when the right  Acme interstage transformer was replaced with a slightly later model. The secondary on this trans. was found to be open and was the only repair that needed to be made to make the radio work again.

While there would be some historical perspective maintained by leaving the spliced buss wires, I just could not do that. So the completed repair is pictured below.
Picture
There appear to be other post-production modifications done to this radio besides the audio trans. repair. Most apparent is the piece of plywood added to the front of the battery storage area. This modification appears to be nearly as old as the radio. The construction of the plywood is period correct and it was stained to match the finish. This mod incorporated a change to the method of B battery attachment. This change made changing batteries much easier. It also allows for the use of both B+ and detector (22.5V) connections.

There is some speculation that a variable cap prior to the detector was replaced with a variometer. While this change might have reduced selectivity it probably improved antenna performance. In 1922 the ability to tune to the antenna is more significant than selectivity since all radio stations were on only ONE or two frequencies. The history of frequency assignment is discussed in the article referenced below.

With or without the variometer there is no signal gain prior to the UV 200 detector. So the "range" of this receiver is very limited. The UV 200 was a good choice at the time but the radio has insufficient control to really take advantage of it. The filament control is very rough and, in the best case, some method of of controlling the detector B+ would have been necessary.
Picture
It is possible that all of the repairs and modifications to this radio were made at the same time. While all of the work appears to be professionally done it also appears to be well planned and the person performing the repair must have been experienced with these modifications.

In my years as a radio tech I participated in several large manufacture's sponsored recalls with required modifications. After a few dozen repairs a tech would get very good at it. In my opinion, repairs to this unit might have been a part of a rebuild/reissue effort.

 I believe that all of the modifications were improvements. Looking at the front panel behind the tuning knob, the panel is neatly and accurately drilled for both a tuning cap (3 holes) and for the variometer (2 holes). All of the holes arel countersunk and clean. This is almost never the case in field modifications.

Consider the possibility that this radio was a warranty repair/return. While very few of these exist there are notes online that seem to indicate that another unit had many similar modifications. A couple of the  early UV type tubes have Pacific States Electric tags. This company was a reseller of considerable size. Is it possible that they acquired returned and unsold units and modified them?
Picture
UV 200 (stock) and UV 201A replacement tubes. The early UV 200 is the tube with no getter.
Below is an explanation for the relatively unselective design of the Acmefone.  This is an excerpt from a remarkably complete history of broadcasting compiled by my friend Ron Kramer.


The contemporary radio listener probably cannot appreciate conditions of radio service in 1922. Stations broadcast sporadically because there were so many trying to use the same frequencies. In fact, in 1921 and early 1922, only one frequency was authorized - 833 KHz (although until about 1930 frequencies were commonly expressed in the actual length of the wave and referred to as wave lengths, in this case 360 meters). All stations broadcast at the same spot on the dial which obviously meant they could not all broadcast at once without interference. In a kind of gentlemens' agreement, they shared the frequency. By late 1922 the growth in the number of stations forced the U.S. Department of Commerce, which was then responsible for radio regulation, to authorize a second frequency of 750 KHz (or 400 meters). Smaller stations, which included those which used phonograph recordings, were required to stay on the old 833 KHz frequency but the first class stations could use 750 KHz, which was a less congested neighborhood.


The complete document was part of an effort to build The Western States Museum of Broadcasting, a project that is on hold, for the moment. It is available as an archived document here:

https://web.archive.org/web/20150404142651/http://www.wsmb.org/Page.asp?NavID=19

If you get a chance , I would recommend reading the entire history. While much of it is specific to  S. Oregon, I am sure that the story was replicated in many large and small communities in the early 1920's

Thanks again to Ron for making this piece of radio history available to us.
Picture
Below are video demonstrations of the Acmefone in operation. There is a considerable improvement in audio using the RCA cone speaker over the onboard horn. Also, the horn driver might have been replace along with the other repairs.
Multiple stations are heard at any setting but tuning the variometer does improve the signal of the local boomer - Spanish language station.
AND for this demonstration I cheated - a little. I substituted my UX 201A substitute tube for the UV 200 detector which allowed for speaker-level audio rather than headphone-level audio. SEE the blog post on tube substitution below.
The Acmefone is now available for viewing by appointment at Russ' Old Radio shop/museum.
5 Comments
Nick Heade
1/23/2018 03:44:00 pm

Hi Russ,

Thanks for sending me the link. The radio looks really good. I forwarded this link to my other family members and let them know they could add additional details about the radio to this blog if they had any.
AL refers to my greatuncle Alfred Huber of Portland Oregon. Born in
1911, he was my Mothers Uncle. I can't recall the exact year of his passing. But he was an avid hiker and camper as a member of the Sierra Club, and film making/photography as a member of the Portland Cine Club.
NIck.

Reply
Arran
2/15/2018 07:56:53 pm

I like the construction of those early radios, they really made them to look like a piece of lab equipment, unfortunately some are better lookers then doers, even by the standards of the time. Is there anything you could do to the horn speaker to improve it's performance, some of those horns have a means to adjust the driver? I've also heard that the magnets in some can get a little weak but can be helped by adding a rare earth magnet to the original.

Reply
Russ
2/16/2018 09:40:49 am

Hi Arran,

Yes some are adjustable, this one is not. I am also sure that the driver (not the horn) is a replacement.

The video illustrated the benefit of a cone (pin type) driver over the older horn. Some of these horns have drivers that are exactly like one side of a 1920s headset. Most of them could be made much better by replacing rubber parts (around the pin and coil) and repolarizing the magnet. I don't usually embark on that task if the driver still works, but someday - -

Reply
Porch Screen Repair Kissimmee, FL link
6/8/2023 01:49:15 am

I have seen this when I was a child. All I can say that is this is so cool and very nice.

Reply
Wedding makeup near me link
6/26/2023 02:21:48 am

Really appreciate you sharing this article post. Thanks Again!

Reply



Leave a Reply.

    Author

                         Russ Webb

    Picture
    Russ Webb & Fuzzy

    Best Buddy, Radio fixer







    Categories

    All
    All
    Antiques
    Electronics
    Radios
    Repair
    Restoration
    Travels
    Vintage

    RSS Feed

    Archives

    March 2025
    November 2024
    December 2023
    March 2023
    November 2022
    October 2022
    July 2022
    January 2022
    December 2021
    September 2021
    June 2021
    April 2021
    February 2021
    January 2021
    November 2020
    July 2020
    June 2020
    April 2020
    March 2020
    December 2019
    October 2019
    May 2019
    April 2019
    March 2019
    February 2019
    January 2019
    December 2018
    November 2018
    October 2018
    September 2018
    June 2018
    April 2018
    March 2018
    February 2018
    January 2018
    December 2017
    November 2017
    September 2017
    June 2017
    May 2017
    April 2017
    February 2017
    December 2016
    November 2016
    October 2016
    September 2016
    August 2016
    July 2016
    June 2016
    May 2016
    April 2016
    March 2016
    February 2016
    January 2016
    December 2015
    November 2015
    August 2015
    June 2015
    May 2015
    April 2015
    March 2015
    February 2015
    January 2015
    December 2014
    November 2014
    October 2014
    September 2014
    August 2014
    July 2014
    June 2014
    May 2014
    April 2014
    March 2014
    February 2014
    January 2014
    December 2013

CUSTOM DESIGN BY SUE WEBB  06/2013       Redesigned by Russ Webb     Approved by Fuzzy   Updated:  Pretty much all the time, but I forget to change this date
Proudly powered by Weebly
Photos from valart2008, rafeejewell